A broken torsion spring is on a metal rod above a garage door.

Highland, Redlands

Spring Repair for Highland's 1980s Garage Doors

Highland homes built around 1982 carry torsion springs sized for that era's doors. Redlands Garage Door Pros drives the 4 miles out to replace them correctly.

(909) 247-3758 Request a quote

Serving Redlands, CABackground-checked techsHonest, upfront pricingFast local response

What It Costs

We don't post a flat number for Highland because spring jobs price out by door weight, wind count, and whether one spring or both need replacing - a double door with both springs gone costs more than a single with one. What we can tell you is that the income profile out here (median household income around $77,979) tracks close to the rest of the service area we cover from Redlands, so pricing isn't adjusted up or down by zip code. You pay for the spring and the labor, not for which suburb you live in.

If you want a number before we show up, describe the door - single or double, the approximate age, and whether it's one spring broken or both - and we can usually give you a range over the phone. A exact quote still needs eyes on the door, because corrosion on the shaft or a bent center bracket changes the job.

A garage door torsion spring is mounted above a metal beam.

The Symptom

A broken torsion spring on a Highland garage almost always shows the same way: the door won't lift, or it lifts a few inches and stops, or the opener strains and the gears inside it grind trying to do a spring's job alone.

Heat hurts coating and motors

Highland sits in a severe-heat climate band, and heat cycling is hard on spring coating and on the opener motors that keep trying to compensate for a dead spring - we see more opener burnout calls here in late summer tied directly to a spring that failed months earlier and was never replaced.

Stop running the opener

If you hear a bang from the garage and the door won't budge afterward, that's the spring snapping, not the opener failing. Don't run the opener again once that happens - it just finishes off the motor and sometimes bends the top panel trying to force a door that's no longer balanced.

The DIY Question

Don't do this one yourself. A wound torsion spring under tension can take a finger or worse if the winding bars slip, and the hardware on a 1982-era door - steel drums, a single center bracket, cables under real load - doesn't forgive a mistake the way a newer nylon-roller setup might. This is the one repair on a garage door where the honest answer is to call someone, not where we're padding the job to bill you.

What you can safely check yourself: whether it's actually the spring and not the opener's travel limits or a dead remote battery. Pull the manual release cord and try lifting the door by hand. If it's dead weight and won't stay up on its own, that's a spring. If it lifts easily and stays put, the problem's electrical, not mechanical, and that's a different call entirely.

How to Book

We cover Highland from our base in Redlands, about 4 miles out, as part of the wider service area that stretches from Mentone through Loma Linda and beyond. There's no separate branch or crew out here - the same truck that handles Redlands jobs makes the drive to Highland, so booking works the same way: call, describe the door and the symptom, and we schedule the visit.

Have the door's rough age and whether it's a single or double door ready when you call - it saves time on the spring order if we need to bring a specific wind length. See our Highland service area page for what else we cover out here, or if you're actually in Redlands proper, the Redlands spring repair page is the one built for that side of the job.

Parts We Carry

Highland's housing stock centers on 1982, which puts most garages here squarely in the torsion-spring era rather than the older extension-spring setups you'll still find on pre-1960s houses elsewhere in the service area.

Springs for builder-grade doors

That means we're stocking torsion springs sized for the steel sectional doors that were standard builder-grade equipment through the 1980s and 90s - wound to match 7-foot and 8-foot door heights, with the center bracket and cable drum hardware that came with them.

Wire size varies by year

We carry a range of wire sizes and wind lengths on the truck because a 1982 door and a 1996 door on the same Highland street don't always take the same spring, even if the garage looks identical from the curb.

Rare builds need ordering

What we don't carry is parts for doors outside that build window - if your house is one of the rarer older or newer builds in the area, we may need to order a spring, which pushes the job out a day or two. We'll tell you on the spot if that's your situation instead of guessing and hoping it fits.

Questions

Common questions

How far out is Highland from your shop?

About 4 miles from our base in Redlands. It's a short drive, and we treat it as a normal stop on the route, not a special trip - same truck, same spring stock, same scheduling as any other call in the service area.

Why does the age of my garage door matter for a spring repair?

Because spring size and winding hardware changed over the decades. Highland's housing mostly dates to around 1982, which means torsion springs sized for that era's steel sectional doors. A much older or newer door can need different hardware, and guessing wrong means a second trip.

Is heat really a factor in spring failure here?

Yes. Highland sits in a severe-heat climate band, and repeated heat cycling degrades spring coating and stresses opener motors that are compensating for a weakening spring. We see a real uptick in both spring and opener calls through the hottest stretch of the year.

Can I just replace one spring if only one broke?

You can, but we don't usually recommend it. Springs wear as a pair, and the second one is often close behind the first. Replacing both at once costs a bit more up front but avoids a second service call a few months later.

Explore more